nl:symmetry:option_borders
This is an old revision of the document!
Table of Contents
Menukeuze "Kaders" (Alt + B)
Toelichting
Wanneer u de “Plaat kaders” een eerste keer aanklik, dan toont het scherm u een aantal uitgegrijsde velden en een blanco voorbeeldscherm (eerste afbeelding). Van zodra u het “Aantal kaders” verhoogt door op het [+]-teken te klikken worden de andere velden en kan u waarden gaan ingeven (tweede afbeelding).
| Aantal kaders | Om in de verschillende velden een waarde te kunnen ingeven en een kadertype te kiezen dient u ten minste één kader te kiezen. Meerdere kaders laten u bovendien toe om verschillende kadertypes te combineren. We zullen het gebruik daarvan toelichten nadat we de verschillende velden hebben overlopen. |
|---|---|
| Geef kader nummer | Wanneer u meer dan 1 kader hebt gekozen, geef dan hier aan welk kadernummer u wil bewerken. |
| Linkermarge | Hier geeft u de mares in: de afstand tussen de kader en de vier plaatranden. |
| Rechtermarge | |
| Bovenmarge | |
| Ondermarge | |
| Hoek Straal | When the border type selected allows, the value you enter for the corner radius will be applied to the 4 corners of your job. |
| Kader type | Please refer to the list of border types below. |
| Kader kleur | Linking a specific colour to a border will allow you to apply specific engraving parameters to this border, just like you can for a coloured text line. |
| Aantal freesbanen | By increasing the number, the border wil be replicated toward the center of the plate as many times as indicated. |
| Baan afstand | The distance between the different cuts. |
Kadertypes
| Plain |  | ||
|---|---|---|---|
| Corner holes |  | Margins | The margins are calculated between the center of the holes and the top and bottom, left and right sides of the plate. For this particular border type, the “corner” radius indicates the radius of the holes. Please see to it that the values entered for the top, bottom, left and right margins are higher than the corner radius. If you enter a radius value higher than the margins’ value, the holes will fall partly outside the margins of the plate. |
| Corner radius | |||
| 2 Fixing holes |  | Margins | The margins are calculated between the center of the holes and the left and right sides of the plate. For this particular border type, the “corner” radius indicates the radius of the holes. Please see to it that the values entered for the left and right margins are higher than the corner radius. If you enter a radius value higher than the margins’ value, the holes will fall partly outside the margins of the plate. |
| Corner radius | |||
| Chamfer |  | Corner radius | The corner radius determines the size of the chamfered corners. |
| Scallop |  | Corner radius | The corner radius determines the size of the scallopped corners. |
| Fillet |  | Corner radius | The corner radius determines the size of the rounded corners. |
| Notch |  | Corner radius | The corner radius determines the size of the notched corners. |
| Ornate |  | Corner radius | The corner radius determines the size of the ornaments. |
| Ellipse |  | Corner radius | The corner radius does not do anything. |
Notes
▪ Number of borders vs. Number of cuts
If you want to apply two (or more) identical borders with a certain offset between them, you will increase the Number of cuts and enter the offset as the Cut separation value. One can obtain the same effect by increasing the Number of borders and adapting the values of the margins for each border. This method is more cumbersome, but allows for more flexibility. For example:
- If you create more than two borders, you can change the offset between each individual pair of borders. Let’s say, for the first border, you enter 5 mm margins, for the second, 10 mm, and for the third 17 mm margins. The offset between border 1 and 2 will be 5 mm, between 2 and 3, it will be 7 mm.
- You can apply a different border colour for each individual border. That way, you can apply a specific cutter to each border and use the outer border to cut through the plate.
However, when using the Number of borders field, when you edit the values of each border, you will only see the active border in the preview. If you want to see the result, you will have to leave the Plate Borders window and return to the main screen.
Obviously, you can also combine the two functions and create two borders, the first having a single cut (to cut out the plate), the second border containing several cuts with an offset between them.
▪ Holes (Corner holes and 2 Fixing holes)
- Normally, when selecting Corner holes or 2 Fixing Holes, you will need to cut deeper into the plate in order to be able to screw the finished plate onto a support or wall.
In order to do so, you can apply a Border colour and link this colour to the same cutter which you use to cut out plates when using Multiplate. Even with a plastic sheet like Graflux only partially pierced through, inserting a screw will be easily done applying some extra force.
Access through
- the [Alt] + [B] keystroke combination
- the Borders shortcut
- the Plate menu - Borders option
A practical Example
 | The first border contains 2 fixing holes (Border type) placed 15 mm (left and right margins) from the side and marked in red (Colour). This will allow us to link this colour to a specific cutter (e.g. a cutter with a cylindrical edge to cut out straight holes, or a V-shaped cutter creating chamfered holes for a philips head screw. |
|
 | The second border contains two (Number of cuts: 2) Ellipses (Border type). The margins between the outer ellipse are 5 mm (Left and Right margin) viz. 13 mm (Top and bottom). These ellipses are in black so they will be engraved using a standard cutter. |
|
 | The third border is a single (Number of cuts: 1) ellipse (Border type) with a 2 mm left and right margin) and a 10 mm top and bottom margin. Its colour is red, since we will use the same cutter with a cylindrical edge as for the 2 fixing holes. |
|
 |  | This is what our end result looks like in the Main Screen, before and after entering a text. When engraved, we will have an oval shaped plaque, with two mounting holes to fix it on a wall or door, and a double ellipse engraved as a border. Feel free to experiment with other combinations as you please ! |
nl/symmetry/option_borders.1655990377.txt.gz · Last modified: 2022/06/23 15:19 by jan.vangelder
