| Both sides previous revision
Previous revision
Next revision
|
Previous revision
|
en:x300:tool_setup [2022/11/19 11:58]
erik.ketele |
en:x300:tool_setup [2023/05/17 10:05] (current)
|
| |
| |{{:en:x300:noseretainerring.png?300x225 }}|* Rotate the graduated nosecone retainer ring up till about 3 or 4 threads are still visible above it.| | |{{:en:x300:noseretainerring.png?300x225 }}|* Rotate the graduated nosecone retainer ring up till about 3 or 4 threads are still visible above it.| |
| |{{:en:x300:dsc_9140.jpg?200 |}} |* Put a metal plate somewhere on the Multimat on the engraving table and move the spindle above it.| | |{{:en:x300:dsc_9140.jpg?200 }}|* Put a metal plate somewhere on the Multimat on the engraving table and move the spindle above it.| |
| |{{:en:x300:dsc_9141.jpg?200 |}} |* Move the spindle down till the nosecone touches the metal plate.| | |{{:en:x300:dsc_9141.jpg?200 }}|* Move the spindle down till the nosecone touches the metal plate.| |
| |{{:en:x300:dsc_9142.jpg?200 |}} |* Put a cutter knob into the spindle and turn it anticlockwise to secure it.| | |{{:en:x300:dsc_9142.jpg?200 }}|* Put a cutter knob into the spindle and turn it anticlockwise to secure it.| |
| |{{:en:x300:dsc_9143.jpg?200 |}} |* Push a cutter through the cutter knob and all the way through the spindle till it touches the metal plate.| | |{{:en:x300:dsc_9143.jpg?200 }}|* Push a cutter through the cutter knob and all the way through the spindle till it touches the metal plate.| |
| |{{:en:x300:dsc_9144.jpg?200 |}} |* Use a 2mm hex wrench to fix the cutter knob to the cutter.| | |{{:en:x300:dsc_9144.jpg?200 }}|* Use a 2mm hex wrench to fix the cutter knob to the cutter.| |
| |{{:en:x300:dsc_9145.jpg?200 |}} |* Unscrew the cutter and the knob from the spindle (unscrew clockwise).| | |{{:en:x300:dsc_9145.jpg?200 }}|* Unscrew the cutter and the knob from the spindle (unscrew clockwise).| |
| |{{:en:x300:dsc_9136.jpg?200 |ASCII}}|* On the Cutter stand screw the depth setting screw all the way down but do not lock it.| | |{{:en:x300:dsc_9136.jpg?200 |ASCII}}|* On the Cutter stand screw the depth setting screw all the way down but do not lock it.| |
| |{{:en:x300:dsc_9135.jpg?200 |ASCII}}|* Put the cutter with the cutter knob into the cutter stand through the black top cylinder with left thread.| | |{{:en:x300:dsc_9135.jpg?200 |ASCII}}|* Put the cutter with the cutter knob into the cutter stand through the black top cylinder with left thread.| |
| ==== Installing an engraving tool ==== | ==== Installing an engraving tool ==== |
| |
| After having calibrated your tools in the tool calibration stand, installing an engraving tool in the spindle is really easy. The cutter with cutter knob has to be screwed counterclockwise into the spindle. Screw and tighten the cutter and its knob by hand, do not use pliers.\\ | After having calibrated your tools in the optional tool calibration stand, installing an engraving tool in the spindle is really easy. The cutter with cutter knob has to be screwed counterclockwise into the spindle. Screw and tighten the cutter and its knob by hand, do not use pliers.\\ |
| In case the cutting depth is not right, you can increase the cutting depth by screwing the depth nose retainer ring up on the spindle, or you can decrease the cutting depth by screwing this graduated ring down. | In case the cutting depth is not right, you can increase the cutting depth by screwing the depth nose retainer ring up on the spindle, or you can decrease the cutting depth by screwing this graduated ring down. |
| |
| {{:en:x300:cutter_nospin.png?50}}A diamond scratch tool is inserted in the spindle just like a normal engraving tool. The only difference with a normal engraving tool is that you preset it, just like a scoring tool, with a washer just under the cutter knob. Another difference with a normal engraving tool is that you do not want the spindle to rotate when a diamond tool is being used. You can select the “no rotation” option for the spindle in the virtual pendant’s menu, as shown below. | {{:en:x300:cutter_nospin.png?50}}A diamond scratch tool is inserted in the spindle just like a normal engraving tool. The only difference with a normal engraving tool is that you preset it, just like a scoring tool, with a washer just under the cutter knob. Another difference with a normal engraving tool is that you do not want the spindle to rotate when a diamond tool is being used. You can select the “no rotation” option for the spindle in the virtual pendant’s menu, as shown below. |
| |
| ==== How to remove a tool from the spindle ==== | **Continue to [[:en:x300:depth_regulator_nose_calibration|depth regulator nose calibration]].**\\ |
| | |
| To remove a tool, you do the opposite of inserting a tool, meaning you unscrew the cutter knob in the clockwise direction. This is the same for engraving, scoring and for diamond scratch tools. | |
| | |
| **Continue to [[depth_regulator_nose_calibration|using the depth regulation nose]].**\\ | |
| **Continue to [[:en:x300:table_of_contents|the table of contents]].** | **Continue to [[:en:x300:table_of_contents|the table of contents]].** |
| |
| |
