| Both sides previous revision
Previous revision
Next revision
|
Previous revision
|
en:x300:tool_setup [2022/09/19 12:07]
erik.ketele |
en:x300:tool_setup [2023/05/17 10:05] (current)
|
| |
| |{{:en:x300:noseretainerring.png?300x225 }}|* Rotate the graduated nosecone retainer ring up till about 3 or 4 threads are still visible above it.| | |{{:en:x300:noseretainerring.png?300x225 }}|* Rotate the graduated nosecone retainer ring up till about 3 or 4 threads are still visible above it.| |
| | |* Put a metal plate somewhere on the Multimat on the engraving table and move the spindle above it.| | |{{:en:x300:dsc_9140.jpg?200 }}|* Put a metal plate somewhere on the Multimat on the engraving table and move the spindle above it.| |
| | |* Move the spindle down till the nosecone touches the metal plate.| | |{{:en:x300:dsc_9141.jpg?200 }}|* Move the spindle down till the nosecone touches the metal plate.| |
| | |* Put a cutter knob into the spindle and turn it anticlockwise to secure it.| | |{{:en:x300:dsc_9142.jpg?200 }}|* Put a cutter knob into the spindle and turn it anticlockwise to secure it.| |
| | |* Push a cutter through the cutter knob and all the way through the spindle till it touches the metal plate.| | |{{:en:x300:dsc_9143.jpg?200 }}|* Push a cutter through the cutter knob and all the way through the spindle till it touches the metal plate.| |
| | |* Use a 2mm hex wrench to fix the cutter knob to the cutter.| | |{{:en:x300:dsc_9144.jpg?200 }}|* Use a 2mm hex wrench to fix the cutter knob to the cutter.| |
| | |* Unscrew the cutter and the knob from the spindle (unscrew clockwise).| | |{{:en:x300:dsc_9145.jpg?200 }}|* Unscrew the cutter and the knob from the spindle (unscrew clockwise).| |
| |{{:en:x300:dsc_9136.jpg?200 |ASCII}}|* On the Cutter stand screw the depth setting screw all the way down but do not lock it.| | |{{:en:x300:dsc_9136.jpg?200 |ASCII}}|* On the Cutter stand screw the depth setting screw all the way down but do not lock it.| |
| |{{:en:x300:dsc_9135.jpg?200 |ASCII}}|* Put the cutter with the cutter knob into the cutter stand through the black top cylinder with left thread.| | |{{:en:x300:dsc_9135.jpg?200 |ASCII}}|* Put the cutter with the cutter knob into the cutter stand through the black top cylinder with left thread.| |
| |{{:en:x300:dsc_9139.jpg?200 |ASCII}}|* Use the locknut to lock the depth setting screw in that position.| | |{{:en:x300:dsc_9139.jpg?200 |ASCII}}|* Use the locknut to lock the depth setting screw in that position.| |
| |{{:en:x300:cutter_stand.png?nolink&250}}|* You can now preset all your cutters in the cutter stand. When you change a cutter in the engraver, it will automatically reach the same engraving depth.| | |{{:en:x300:cutter_stand.png?nolink&250}}|* You can now preset all your cutters in the cutter stand. When you change a cutter in the engraver, it will automatically reach the same engraving depth.| |
| |
| * Rotate the graduated nosecone retainer ring up till about 3 or 4 threads are still visible above it.\\ | |
| * Put a metal plate somewhere on the Multimat on the engraving table and move the spindle above it.\\ | |
| * Move the spindle down till the nosecone touches the metal plate.\\ | |
| * Put a cutter knob into the spindle and turn it anticlockwise to secure it.\\ | |
| * Push a cutter through the cutter knob and all the way through the spindle till it touches the metal plate.\\ | |
| * Use a 2mm hex wrench to fix the cutter knob to the cutter.\\ | |
| * Unscrew the cutter and the knob from the spindle (unscrew clockwise).\\ | |
| * On the Cutter stand screw the depth setting screw all the way down but do not lock it.\\ | |
| * Put the cutter with the cutter knob into the cutter stand and screw it anticlockwise to lock them.\\ | |
| * Gently rotate the depth setting screw up till it touches the cutter tip.\\ | |
| * Use the locknut to lock the depth setting screw in that position.\\ | |
| * You can now preset all your cutters in the cutter stand. When you change a cutter in the engraver, it will automatically reach the same engraving depth. | |
| |
| ==== Installing an engraving tool ==== | ==== Installing an engraving tool ==== |
| {{:en:x300:cutter_nospin.png?50}}A diamond scratch tool is inserted in the spindle just like a normal engraving tool. The only difference with a normal engraving tool is that you preset it, just like a scoring tool, with a washer just under the cutter knob. Another difference with a normal engraving tool is that you do not want the spindle to rotate when a diamond tool is being used. You can select the “no rotation” option for the spindle in the virtual pendant’s menu, as shown below. | {{:en:x300:cutter_nospin.png?50}}A diamond scratch tool is inserted in the spindle just like a normal engraving tool. The only difference with a normal engraving tool is that you preset it, just like a scoring tool, with a washer just under the cutter knob. Another difference with a normal engraving tool is that you do not want the spindle to rotate when a diamond tool is being used. You can select the “no rotation” option for the spindle in the virtual pendant’s menu, as shown below. |
| |
| ==== How to remove a tool from the spindle ==== | **Continue to [[:en:x300:depth_regulator_nose_calibration|depth regulator nose calibration]].**\\ |
| | |
| To remove a tool, you do the opposite of inserting a tool, meaning you unscrew the cutter knob in the clockwise direction. This is the same for engraving, scoring and for diamond scratch tools. | |
| **Continue to [[:en:x300:table_of_contents|the table of contents]].** | **Continue to [[:en:x300:table_of_contents|the table of contents]].** |
| |
| |
