Differences

This shows you the differences between two versions of the page.

--- en:x300:tool_setup [2022/09/19 11:05]
erik.ketele
+++ en:x300:tool_setup [2023/05/17 10:05] (current)
@@ Line 3: / Line 3: @@
 ==== How to use the cutter calibration stand ====
-{{:en:x300:cutter_stand.png?nolink&250}}{{:en:x300:noseretainerring.png?300x225  }}
+|{{:en:x300:noseretainerring.png?300x225  }}|* Rotate the graduated nosecone retainer ring up till about 3 or 4 threads are still visible above it.|
+|{{:en:x300:dsc_9140.jpg?200  }}|* Put a metal plate somewhere on the Multimat on the engraving table and move the spindle above it.|
-* Rotate the graduated nosecone retainer ring up till about 3 or 4 threads are still visible above it.\\
+|{{:en:x300:dsc_9141.jpg?200  }}|* Move the spindle down till the nosecone touches the metal plate.|
-* Put a metal plate somewhere on the Multimat on the engraving table and move the spindle above it.\\
+|{{:en:x300:dsc_9142.jpg?200  }}|* Put a cutter knob into the spindle and turn it anticlockwise to secure it.|
-* Move the spindle down till the nosecone touches the metal plate.\\
+|{{:en:x300:dsc_9143.jpg?200  }}|* Push a cutter through the cutter knob and all the way through the spindle till it touches the metal plate.|
-* Put a cutter knob into the spindle and turn it anticlockwise to secure it.\\
+|{{:en:x300:dsc_9144.jpg?200  }}|* Use a 2mm hex wrench to fix the cutter knob to the cutter.|
-* Push a cutter through the cutter knob and all the way through the spindle till it touches the metal plate.\\
+|{{:en:x300:dsc_9145.jpg?200  }}|* Unscrew the cutter and the knob from the spindle (unscrew clockwise).|
-* Use a 2mm hex wrench to fix the cutter knob to the cutter.\\
+|{{:en:x300:dsc_9136.jpg?200  |ASCII}}|* On the Cutter stand screw the depth setting screw all the way down but do not lock it.|
-* Unscrew the cutter and the knob from the spindle (unscrew clockwise).\\
+|{{:en:x300:dsc_9135.jpg?200  |ASCII}}|* Put the cutter with the cutter knob into the cutter stand through the black top cylinder with left thread.|
-* On the Cutter stand screw the depth setting screw all the way down but do not lock it.\\
+|{{:en:x300:dsc_9137.jpg?200  |ASCII}}|* Screw the cutter knob and the cutter anticlockwise to lock them.|
-* Put the cutter with the cutter knob into the cutter stand and screw it anticlockwise to lock them.\\
+|{{:en:x300:dsc_9138.jpg?200  |ASCII}}|* Gently rotate the depth setting screw up till it touches the cutter tip.|
-* Gently rotate the depth setting screw up till it touches the cutter tip.\\
+|{{:en:x300:dsc_9139.jpg?200  |ASCII}}|* Use the locknut to lock the depth setting screw in that position.|
-* Use the locknut to lock the depth setting screw in that position.\\
+|{{:en:x300:cutter_stand.png?nolink&250}}|* You can now preset all your cutters in the cutter stand. When you change a cutter in the engraver, it will automatically reach the same engraving depth.|
-* You can now preset all your cutters in the cutter stand. When you change a cutter in the engraver, it will automatically reach the same engraving depth.
 ==== Installing an engraving tool ====
@@ Line 29: / Line 28: @@
 ==== Installing a diamond scratch tool ====
-A diamond scratch tool is inserted in the spindle just like a normal engraving tool. The only difference with a normal engraving tool is that you preset it, just like a scoring tool, with a washer just under the cutter knob. Another difference with a normal engraving tool is that you do not want the spindle to rotate when a diamond tool is being used. You can select the “no rotation” option for the spindle in the virtual pendant’s menu, as shown below.
+{{:en:x300:cutter_nospin.png?50}}A diamond scratch tool is inserted in the spindle just like a normal engraving tool. The only difference with a normal engraving tool is that you preset it, just like a scoring tool, with a washer just under the cutter knob. Another difference with a normal engraving tool is that you do not want the spindle to rotate when a diamond tool is being used. You can select the “no rotation” option for the spindle in the virtual pendant’s menu, as shown below.
-==== How to remove a tool from the spindle ====
-To remove a tool, you do the opposite of inserting a tool, meaning you unscrew the cutter knob in the clockwise direction. This is the same for engraving, scoring and for diamond scratch tools. **Continue to [[:en:x300:table_of_contents|the table of contents]].**
+**Continue to [[:en:x300:depth_regulator_nose_calibration|depth regulator nose calibration]].**\\
+**Continue to [[:en:x300:table_of_contents|the table of contents]].**

cyborg-engravers

User Tools

Site Tools

Differences

Page Tools