Differences

This shows you the differences between two versions of the page.

--- en:x300:table_of_contents [2022/09/21 12:12]
erik.ketele [Chapter 3 – Preparing and executing an engraving job]
+++ en:x300:table_of_contents [2023/05/17 10:05] (current)
@@ Line 40: / Line 40: @@
   * [[:en:x300:system_requirements|2.4.1. System requirements]]
-  * [[:en:x300:pendent_installation_standalone|2.4.2. Installing the Cyborg virtual pendent for a standalone computer]]
+  * [[:en:x300:configuring_the_pc_ethernet_port|2.4.2. Configuring the PC's ethernet port]]
+  * [[:en:x300:pendent_installation_standalone|2.4.3. Installing the Cyborg virtual pendent]]
   * [[:en:x300:pendent_registration|2.4.4. Registering and starting the Cyborg pendent software]]
   * [[:en:symmetry:installation|2.4.5. Installing the “Symmetry” engraving software]]
@@ Line 101: / Line 102: @@
 === 4.2. Periodical maintenance ===
-  * 4.2.1. Daily
+  * 4.2.1. [[:en:x300:daily|daily maintenance]]
-  * 4.2.2. Weekly
+  * 4.2.2. [[:en:x300:weekly|weekly maintenance]]
-  * 4.2.3. Monthly
+  * 4.2.3. [[:en:x300:monthly|monthly maintenance]]
-  * 4.2.4. Annual
+  * 4.2.4. [[:en:x300:annual|annual maintenance]]
-=== 4.3. Basic maintenance ===
+=== 4.3. Advanced maintenance ===
   * 4.3.1. [[:en:x300:spindle_belt_replacement|Replacing the spindle belt]]
   * 4.3.2. [[:en:x300:timing_belt_tensioning|Tensioning the timing belts]]
   * 4.3.3. [[:en:x300:machine_cover_removal|Removing the machine covers]]
-=== 4.4. Overview of maintenance activities ===
 ===== Chapter 5 – Troubleshooting =====
@@ Line 123: / Line 122: @@
 **[[:en:x300:no_pc_connection|5.4. No connection between machine and computer]]**
-**[[:en:x300:wrong_driver|5.5. Symmetry has not been set up with the right driver]]**
-===== Chapter 6 – Electrical rating and identification plate =====
-nog blanco in het Word-document - verplaatst naar Introduction (specs) en 1.2.4. (identification plate)
-=== (6.1. Power consumption) ===
-=== (6.2. Identification plate and serial number) ===
-----
-===== Chapter 7 – Options =====
-  * 7.1. Vacuum converter
-  * 7.2. Self centering vise
-  * 7.3. Jigs for the clamping vise
-  * 7.4. Output signal for switching on and off an external device at the beginning and the end of a job
-  * 7.5. Output signal for switching on and off an external device at every spindle up/down move
-----
-===== Appendices =====
-**[[:en:x300:thesaurus|A. Thesaurus: a glossary with specific terms about all things computerized engraving as being used in this manual.]]**
-**[[:en:x300:g-code_and_m-code|B. G-code and M-code protocol for the Cyborg controller.]]**
-===== Chapter 4 – Maintenance and cleaning =====
-=== 4.1. Cleaning – a must to prolong your machine’s lifetime ===
-=== 4.2. Periodical maintenance ===
-  * 4.2.1. Daily
-  * 4.2.2. Weekly
-  * 4.2.3. Monthly
-  * 4.2.4. Annual
-=== 4.3. Basic maintenance ===
-  * 4.3.1. [[:en:x300:spindle_belt_replacement|Replacing the spindle belt]]
-  * 4.3.2. [[:en:x300:timing_belt_tensioning|Tensioning the timing belts]]
-  * 4.3.3. [[:en:x300:machine_cover_removal|Removing the machine covers]]
-=== 4.4. Overview of maintenance activities ===
-===== Chapter 5 – Troubleshooting =====
-**[[:en:x300:machine_not_initializing|5.1. The machine does not initialize]]**
-**[[:en:x300:spindle_not_rotating|5.2. The spindle does not rotate]]**
-**[[:en:x300:poor_engraving_results|5.3. The engraving results are poor]]**
-**[[:en:x300:no_pc_connection|5.4. No connection between machine and computer]]**
-**[[:en:x300:wrong_driver|5.5. Symmetry has not been set up with the right driver]]**
-===== Chapter 6 – Electrical rating and identification plate =====
-nog blanco in het Word-document - verplaatst naar Introduction (specs) en 1.2.4. (identification plate)
-=== (6.1. Power consumption) ===
-=== (6.2. Identification plate and serial number) ===
 ----
-===== Chapter 7 – Options =====
+===== Chapter 6 – Options =====
   * 7.1. Vacuum converter

cyborg-engravers

User Tools

Site Tools

Differences

Page Tools