Differences

This shows you the differences between two versions of the page.

--- en:x300:table_of_contents [2022/09/21 11:40]
erik.ketele [Chapter 2 – Installation and setup]
+++ en:x300:table_of_contents [2023/05/17 10:05] (current)
@@ Line 40: / Line 40: @@
   * [[:en:x300:system_requirements|2.4.1. System requirements]]
-  * [[:en:x300:pendent_installation_standalone|2.4.2. Installing the Cyborg virtual pendent for a standalone computer]]
+  * [[:en:x300:configuring_the_pc_ethernet_port|2.4.2. Configuring the PC's ethernet port]]
+  * [[:en:x300:pendent_installation_standalone|2.4.3. Installing the Cyborg virtual pendent]]
   * [[:en:x300:pendent_registration|2.4.4. Registering and starting the Cyborg pendent software]]
-  * [[:en:x300:symmetry:installation|2.4.5. Installing the “Symmetry” engraving software]]
+  * [[:en:symmetry:installation|2.4.5. Installing the “Symmetry” engraving software]]
   * [[:en:x300:third_party_software|2.4.6. Using other third party software]]
@@ Line 84: / Line 85: @@
   * 3.5.4. [[:en:x300:pause_button|Pause button]]
   * 3.5.5. [[:en:x300:cancel_a_job|Cancelling the engraving job]]
-  * 3.5.6. [[:en:x300:restarting_proximity_restart|Proximity restart]]
+  * 3.5.6. [[:en:x300:restarting_job_console|Restarting the engraving job]]
-  * 3.5.7. [[:en:x300:restarting_job_console|Restarting the engraving job using "job console"]]
 === 3.6. Controlling the X-300 using the ‘virtual keypad’ ===
@@ Line 102: / Line 102: @@
 === 4.2. Periodical maintenance ===
-  * 4.2.1. Daily
+  * 4.2.1. [[:en:x300:daily|daily maintenance]]
-  * 4.2.2. Weekly
+  * 4.2.2. [[:en:x300:weekly|weekly maintenance]]
-  * 4.2.3. Monthly
+  * 4.2.3. [[:en:x300:monthly|monthly maintenance]]
-  * 4.2.4. Annual
+  * 4.2.4. [[:en:x300:annual|annual maintenance]]
-=== 4.3. Basic maintenance ===
+=== 4.3. Advanced maintenance ===
   * 4.3.1. [[:en:x300:spindle_belt_replacement|Replacing the spindle belt]]
   * 4.3.2. [[:en:x300:timing_belt_tensioning|Tensioning the timing belts]]
   * 4.3.3. [[:en:x300:machine_cover_removal|Removing the machine covers]]
-=== 4.4. Overview of maintenance activities ===
 ===== Chapter 5 – Troubleshooting =====
@@ Line 124: / Line 122: @@
 **[[:en:x300:no_pc_connection|5.4. No connection between machine and computer]]**
-**[[:en:x300:wrong_driver|5.5. Symmetry has not been set up with the right driver]]**
-===== Chapter 6 – Electrical rating and identification plate =====
-nog blanco in het Word-document - verplaatst naar Introduction (specs) en 1.2.4. (identification plate)
-=== (6.1. Power consumption) ===
-=== (6.2. Identification plate and serial number) ===
 ----
-===== Chapter 7 – Options =====
+===== Chapter 6 – Options =====
   * 7.1. Vacuum converter

cyborg-engravers

User Tools

Site Tools

Differences

Page Tools