cyborg-engravers

User Tools

Site Tools

Trace:
en:x300:pendent_registration

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
en:x300:pendent_registration [2022/09/24 20:53]
erik.ketele 		en:x300:pendent_registration [2025/04/17 16:10] (current)
erik.ketele
Line 7: Line 7:
 In order to be able to use the virtual pendent software, it has to be registered. In the top bar of the Cyborg virtual pendent right click on the “?”, and then on the “register” menu option. In order to be able to use the virtual pendent software, it has to be registered. In the top bar of the Cyborg virtual pendent right click on the “?”, and then on the “register” menu option.
  
-|{{:en:x300:register1.jpg?400  |register1.jpg}} |<font 11.0pt/Arial,sans-serif;;black;;inherit>If a window such as the one here on the left appears then something is wrong with your ethernet connection, or with the ethernet cable, or the X-300 has not been switched on.</font> |+|{{:en:x300:register1.jpg?400  |register1.jpg}}|<font 11.0pt/Arial,sans-serif;;black;;inherit>If a window such as the one here on the left appears then something is wrong with your ethernet connection, or with the ethernet cable, or the X-300 has not been switched on.</font> |
 |{{:en:x300:register-ok.png?400  |register2.jpg}}|<font 11.0pt/Arial,sans-serif;;black;;inherit>When the ethernet connection between your pc and the Cyborg X-300 has been configured correctly and the Cyborg X-300 has been switched on, then the registration window will display \\ |{{:en:x300:register-ok.png?400  |register2.jpg}}|<font 11.0pt/Arial,sans-serif;;black;;inherit>When the ethernet connection between your pc and the Cyborg X-300 has been configured correctly and the Cyborg X-300 has been switched on, then the registration window will display \\
 the machine’s mac address in the “customer number” field. This is a unique code which is linked to the X-300 cnc controller. \\ the machine’s mac address in the “customer number” field. This is a unique code which is linked to the X-300 cnc controller. \\
Line 20: Line 20:
 Over the virtual pendent you will see a little window in which the following message is displayed: "I have read and understood the Operator’s Manual”. Over the virtual pendent you will see a little window in which the following message is displayed: "I have read and understood the Operator’s Manual”.
  
-|  {{:en:x300:understood.jpg?200|understood.jpg}}  |<font 11.0pt/Arial,sans-serif;;black;;inherit>You will have to click the OK button to be able to work with the virtual pendent.\\ +|  {{:en:x300:understood.jpg?200|understood.jpg}}  |<font 11.0pt/Arial,sans-serif;;black;;inherit>You will have to click the OK button to be able to work with the virtual pendent. \\ 
-This message is important!\\ +This message is important! \\ 
-By clicking OK you testify that you have actually read and that you have completely understood the contents of this manual.\\ +By clicking OK you testify that you have actually read and that you have completely understood the contents of this manual. \\ 
-Hence, if you have not read, or if you have not fully understood this entire manual, you should not click this OK button. If you have read and understood this manual, click the OK button.\\+Hence, if you have not read, or if you have not fully understood this entire manual, you should not click this OK button. If you have read and understood this manual, click the OK button. \\
 After having done so, the window with the warning message disappears.</font> | After having done so, the window with the warning message disappears.</font> |
-|{{:en:x300:startup_kap_toedoen_v2.png?310}}|<font 11.0pt/Arial,sans-serif;;black;;inherit>Before you can actually use the machine to engrave you will have to home it.\\ +|{{:en:x300:startup_kap_toedoen_v2.png?310}}|<font 11.0pt/Arial,sans-serif;;black;;inherit>Before you can actually use the machine to engrave you will have to home it. \\ 
-In other words the machine has to find its limits and position itself over the top left corner of the engraving table. That is where the home position is.\\ +In other words the machine has to find its limits and position itself over the top left corner of the engraving table. That is where the home position is. \\ 
-The home position is indicated with the coordinates (0,0). +The home position is indicated with the coordinates (0,0). \\ 
-To home the machine press the {{:en:x300:key_shift.png?20|}} (shift) and the {{:en:x300:key_gohome.png?20|}} (go home) keys one after another. If the machine’s protective cover was not closed when you try to home, the following will appear on your computer screen (see image on the left):</font> | +\\ 
 +To home the machine press the  (shift) and the  (go home) keys one after another. \\ 
 +If the machine’s protective cover was not closed when you try to home, the following will appear on your computer screen (see image on the left): \\ 
 +\\ 
 +Close the protective cover, the bitmap with the yellow arrow will disappear and you can restart the homing cycle by pushing  and  again. \\ 
 +\\ 
 +If you click OK without having closed the protective cover, the window with the image to close the lid will also disappear, \\ 
 +but it will be displayed again when you re-try to home the machine. \\ 
 +\\ 
 +Hence remember that you can only home the machine with the protective cover closed.</font> |
  
 ====   ==== ====   ====
en/x300/pendent_registration.1664045630.txt.gz · Last modified: 2022/09/24 20:53 by erik.ketele

Page Tools

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki