en:x300:adjusting_feeds_and_speeds
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
en:x300:adjusting_feeds_and_speeds [2022/09/21 12:09] erik.ketele |
en:x300:adjusting_feeds_and_speeds [2023/10/20 10:17] (current) jan.vangelder |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Adjusting feeds and speeds during cutting ====== | ====== Adjusting feeds and speeds during cutting ====== | ||
| - | Depending upon your engraving or routing software, feeds (mm/sec or m/min) and speeds (rpm) can or cannot be entered. If the resulting cnc files do not contain feeds and speeds, the system will use the speed and feed parameters which have been predefined in the virtual pendent' | + | ---- |
| + | |||
| + | Depending upon your engraving or routing software, feeds (mm/sec or m/min) and speeds (rpm) can or cannot be entered. If the resulting cnc files do not contain feeds and speeds, the system will use the speed and feed parameters which have been predefined in the virtual pendent' | ||
| === Spindle speed (rotational speed in rpm) === | === Spindle speed (rotational speed in rpm) === | ||
| - | While engraving, it is possible to continuously adapt the rotary speed of the engraving spindle, between the minimum of 6000 rpm and the maximum of 20000 rpm. To lower the speed, click the [[: | + | While engraving, it is possible to continuously adapt the rotary speed of the engraving spindle, between the minimum of 6000 rpm and the maximum of 20000 rpm. To lower the speed, click the {{:en:x300:key_rpmdecrease.png?30|}} key. Each click will lower the speed with 100 RPM. To increase the speed, click the {{:en:x300:key_rpmincrease.png?30|}} key. Each click will increase the speed with 100 RPM. Lowering or increasing the rotational speed of the cutter can be done on the fly, while the machine continues to engrave. |
| === Feed (moving speed, displayed in mm per sec) === | === Feed (moving speed, displayed in mm per sec) === | ||
| Line 11: | Line 13: | ||
| While engraving, it is also possible to modify the feed on the fly. The feed is also limited between a minimum and a maximum speed, the minimum speed being 1% of the preprogrammed moving speed in the job, the maximum speed 150% of the preprogrammed moving speed in the job. It is not possible to increase the feed higher than 1.5 times the preprogrammed speed. The chosen percentage is applied to both the XY and the Z speeds. | While engraving, it is also possible to modify the feed on the fly. The feed is also limited between a minimum and a maximum speed, the minimum speed being 1% of the preprogrammed moving speed in the job, the maximum speed 150% of the preprogrammed moving speed in the job. It is not possible to increase the feed higher than 1.5 times the preprogrammed speed. The chosen percentage is applied to both the XY and the Z speeds. | ||
| - | To increase the feed, click the [[: | + | To increase the feed, click the {{:en:x300:key_feedincrease.png?30|}} key on your virtual keypad. To decrease the feed, click the {{:en:x300:key_feeddecrease.png?30|}} key on your virtual keypad. |
| |**Example: | |**Example: | ||
| Line 21: | Line 23: | ||
| | 150%| 75 mm/ | | 150%| 75 mm/ | ||
| + | **Continue to [[pause_button|the pause key]].**\\ | ||
| **Continue to [[: | **Continue to [[: | ||
en/x300/adjusting_feeds_and_speeds.1663754961.txt.gz · Last modified: 2022/09/21 12:09 by erik.ketele
