cyborg-engravers

User Tools

Site Tools

Trace:
en:x200:spindle_pressure_spring

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
en:x200:spindle_pressure_spring [2025/04/18 10:38]
erik.ketele 		en:x200:spindle_pressure_spring [2025/04/18 15:02] (current)
erik.ketele
Line 12: Line 12:
 |**Note:** **Be extremely careful never to use the nosecone on your spindle when the spring pressure lockring is down.** You may harm your Z-axis motor, the Z-axis leadscrew and even the controller. In other words, always respect the following principle: Never launch an engraving cycle with both the nosecone on the spindle and the spring pressure lock ring screwed down.  | |**Note:** **Be extremely careful never to use the nosecone on your spindle when the spring pressure lockring is down.** You may harm your Z-axis motor, the Z-axis leadscrew and even the controller. In other words, always respect the following principle: Never launch an engraving cycle with both the nosecone on the spindle and the spring pressure lock ring screwed down.  |
  
-==== Setting the plate surface with spring pressure lockring in the up position and then engraving with this ring locked in the down position ====+==== Setting the plate surface with spring pressure lockring in the down position ====
  
 Here above you can read how the lockring can be screwed up and down, and how the nosecone holder ring can be screwed off the spindle. Here above you can read how the lockring can be screwed up and down, and how the nosecone holder ring can be screwed off the spindle.
Line 25: Line 25:
   - Move the spindle somewhere over the plate to be engraved. Use the jog keys on the virtual keypad to do so.   - Move the spindle somewhere over the plate to be engraved. Use the jog keys on the virtual keypad to do so.
   - Using the Z-down jog key move the spindle down till the tip of the cutter just touches the plate surface. You could use a piece of paper to "feel" if the Z-position is correct. Attention: Do not move down too fast, you might damage the material or break the cutter tip.   - Using the Z-down jog key move the spindle down till the tip of the cutter just touches the plate surface. You could use a piece of paper to "feel" if the Z-position is correct. Attention: Do not move down too fast, you might damage the material or break the cutter tip.
-  - Click on "stel materiaal oppervlakte in" toets: {{:en:x300:key_surface.png?30}}op het virtuele toetsenbord. +  - Click on the "set material surface" key: {{:en:x300:key_surface.png?30}} on the virtual keypad. 
-  - Klik in dit net geopende venstertje op de “Enter” knop om de plaatoppervlakte in te stellen (Z=0.00). De spindel zal vervolgens omhoog bewegen boven het graveermateriaal. +  - In this just opened window click on the “Enter” key to set the plate surface (Z=0.00). The spindle will then move up above the engraving material. 
-  - Deze procedure impliceert dat de frees het graveermateriaal zal raken. Als dat niet mag, bv. omdat het graveermateriaal zou kunnen beschadigen, kun je een dun plaatje boven op je graveermateriaal leggen, waarvan je de exacte dikte kent. Denk eraan dat de dikte van dit tussenplaatje bijgeteld moet worden bij je graveerdiepte om een correcte gegraveerde diepte te bekomen. +  - This procedure implies that the tip of the cutter will touch the material. If that is prohibited, e.g. because the material is very critical to scratches, you could place a thin piece of material on top of your engraving plate and follow the same procedure. Measure the exact thickness of this piece and add that to the engraving depth in Symmetry to obtain the correct engraving depth. 
-  - Start je graveerjob.+  - Start your engraving job. 
 + 
 +As an alternative to this procedure you could also follow these steps: 
 + 
 +  - follow the steps from 1 to 6 as described here above. 
 +  - Using the Z-down key move the spindle down till the tip of the cutter is a few millimeters above the plate surface, but not touching it. 
 +  - Unscrew the little screw in the cutter knob and gently push the cutter down till it's tip touches the material. 
 +  - Retighthen the screw in the cutter knob. 
 +  - Click on the "set material surface" key: {{:en:x300:key_surface.png?30}} on the virtual keypad. 
 +  - In this just opened window click on the “Enter” key to set the plate surface (Z=0.00). The spindle will then move up above the engraving material.
  
 === Nota's: === === Nota's: ===
Line 34: Line 43:
 {{:nl:x200:zmove_fromjobfile.png?600}} {{:nl:x200:zmove_fromjobfile.png?600}}
  
-Wanneer zonder neusconus en met een geblokkeerd vlottend mechanisme gewerkt wordt, zal de machine de dieptes uitvoeren die in de graveerjob zitten, op voorwaarde dat in het Job dialog venster (zie hierboven) de "Z move values" in gesteld werd op "From Job File". Of je graveerjob dieptes bevat hangt uitsluitend af van de gebruikte software. Sommige programma’s gebruiken Z-omlaag en Z-omhoog waardes, andere programma’s gebruiken alleen “omlaag” en een “omhoog” instructie, zonder opgave van een waarde. In dit laatste geval moet in dit dialog venster de "Z Move Values" ingesteld worden op "From Pendent setting". De graveermachine zal dan een voorgeprogrammeerde diepte gebruiken, die ook ingegeven of gewijzigd kan worden via het “Job dialoog venster” in het virtuele toetsenbord.+When engraving without nosecone and with a locked floating mechanism, the machine will execute the cutting depths which are programmed in the engraving job, on condition that the variable "Z move values" in the Job dialog window (see here above) is set to "From job file". If your engraving job contains cutting depths or not entirely depends upon the used software. Some programs use Z-down and Z-up values, other programs use Z-down coordinates but only a Z-up instuction without value.  In the latter case the "Z move values" variable in the dialog window has to be set to "From Pendent Setting".  The engraving machine will then use a preset depth, which can be set or modified in the "Job dialog window" in the virtual keypad.
  
-**Continue to [[materials_rpm_feed|speeds and feeds for different materials]].**\\+**Continue to [[engraving_without_floating_nose|engraving without floating nosecone]].**\\
 **Continue to [[:en:x200:table_of_contents|the table of contents]].** **Continue to [[:en:x200:table_of_contents|the table of contents]].**
  
  
en/x200/spindle_pressure_spring.1744965482.txt.gz · Last modified: 2025/04/18 10:38 by erik.ketele

Page Tools

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki