Differences

This shows you the differences between two versions of the page.

--- en:x200:set_surface_key [2025/04/22 10:57]
erik.ketele created
+++ en:x200:set_surface_key [2025/04/22 11:11] (current)
erik.ketele
@@ Line 5: / Line 5: @@
 Before using this key, you have to make sure the spring retainer ring is not locked.\\
-The "set material surface" function can only be used if your pendant displays {{:en:x300:plate_surface_set_v2.png?100|}} or {{:en:x300:plate_surface_map_v2.png?100|}}.\\
 Once the material surface is set you should not have to reset it again unless:\\
@@ Line 13: / Line 12: @@
 \\
 ----
-\\
-{{:en:x300:plate_surface_set_v2.png?200|}}\\
 \\
 Press the JOG ARROWS keys {{:en:x300:key_left.png?20}}{{:en:x300:key_right.png?20}}{{:en:x300:key_up.png?20}}{{:en:x300:key_dn.png?20}} to position the cutter anywhere over the material.\\
-Press the SURFACE {{:en:x300:key_surface.png?20}} key. This will open the following window:\\
+Then slowly jog the spindle down {{:en:x300:key_zdn.png?20|}} till the nosecone just touches the material. That is where you want the Z-axis setting to be Z=0.0 \\
-{{:en:x300:set_surface.jpg?200|}}\\
+After that, press the SURFACE {{:en:x300:key_surface.png?20}} key. This will open the following window:\\
+{{:nl:x200:x200_setsurface.png?200|}}\\
 \\
-. You can now (continuously) push the probe button {{:en:x300:probe.jpg?150|}}. The spindle will slowly move down and set the plate surface.\\
+Here you can still manually move the spindle down {{:en:x300:key_zdn.png?20|}} till it just touches the material surface and hit the Enter {{:en:x300:key_enter.png?20|}} key in the set surface window.\\
-. Or you can manually move the spindle down {{:en:x300:key_zdn.png?20|}} till it just touches the material surface and hit the Enter {{:en:x300:key_enter.png?20|}} key in the set surface window.\\
 \\
-----
-{{:en:x300:plate_surface_map_v2.png?200|}}\\
-\\
-Press the JOG ARROWS keys {{:en:x300:key_left.png?20}}{{:en:x300:key_right.png?20}}{{:en:x300:key_up.png?20}}{{:en:x300:key_dn.png?20}} to position the cutter on the upper left corner of the imaginary rectangle of which you want to scan the relief.\\
-Press the SURFACE {{:en:x300:key_surface.png?20}} key. This will open the following window:\\
-{{:en:x300:surface_map.jpg?350|}}\\
-\\
-Fill in the data as you like. You can read further information in the bottom part of **[[spindle_pressure_spring|this page]]**\\
+**Return to [[:en:x200:keypad_overview|the keypad overview]].** \\
-\\
+**Continue to [[:en:x200:table_of_contents|the table of contents]].**
-**Return to [[:en:x300:keypad_overview|the keypad overview]].** \\
-**Continue to [[:en:x300:table_of_contents|the table of contents]].**

cyborg-engravers

User Tools

Site Tools

Differences

Page Tools