Differences

This shows you the differences between two versions of the page.

--- en:x200:move_to_xyz_key [2025/04/22 11:54]
erik.ketele
+++ en:x200:move_to_xyz_key [2025/04/22 12:12] (current)
erik.ketele
@@ Line 1: / Line 1: @@
 ====== Move to XYZ-coordinate ======
-The MOVE command allows you to enter exact values for X, Y, or Z (0,0,0) where the first entry is X, the second entry is Y, and the third entry is Z. The X, Y, and Z values will reference from the machine's Hard Home position until the SET HOME and SET SURFACE commands have been selected. At that point the X and Y axis will reference from the Set Home position. The Z value will reference from the surface of the material.
+The MOVE command allows you to enter exact values for X, Y, or Z (0,0,0) where the first entry is X, the second entry is Y, and the third entry is Z. \\
+The X, Y, and Z values will reference from the machine’s Hard Home position until the SET HOME and SET SURFACE commands have been selected.\\
+At that point the X and Y axis will reference from the Set Home position. The Z value will reference from the surface of the material if the surface has been set.
 To Move To A Specific Location.
-Press the MOVE   hot key. \\
+Press the MOVE hot key.\\
-Enter the desired value for X from the number pad (50.0 for example).
+Enter the desired value for X from the number pad (50.0 for example).\\
-{{:en:x200:movetoxyz-x.png?200}} \\
+{{:en:x200:movetoxyz-x.png?200}}\\
-Press ENTER   to accept the value.
+Press ENTER to accept the value.
-Keypad Display:
+Enter the desired value for Y from the number pad (-50.0 for example). Press ENTER to accept the value.\\
-   " Move To "
+{{:en:x200:movetoxyz-y.png?200}}
-   " X ###.#### "
-   " Y ###.#### "
-Enter the desired value for Y from the number pad (-50.0 for example). Press ENTER   to accept the value.
+Enter the desired value for Z from the number pad (5.0 for example). Press ENTER to accept the value.\\
+{{:en:x200:movetoxyz-z.png?200}}
-Keypad Display:
+When the coordinates have been entered, click on the **Move** button.\\
-  " Move To "
+{{:en:x200:movetoxyz-move.png?200}}\\
-  " X ###.#### "
+When pushing the **Move** button the machine will move to the new coordinates. If for some reason you do not want to move to the entered coordinates, hit the **Cancel** key.\\ \\
-  " Y ###.#### "
+After the move you will see the new coordinates in the top part of the pendent window:\\
-  " Z ###.#### "
+{{:en:x200:movetoxyz-coord.png?300}}\\
-Enter the desired value for Z from the number pad (-2.0 for example). Press ENTER   to accept the value.
-Keypad Display:
-  " Move To "
-  " X ###.#### "
-  " Y ###.#### "
-  " Z ###.#### " " ? "
-When the "?" is displayed, press ENTER   to accept all settings and move the machine to the new coordinates.
-The above steps will be repeated until you press the CANCEL   hot key to return the Main Display.
-=== Note: ===
-When the X, Y, or Z value comes up it will be in the current location of that axis. If the current location is required select MOVE   and Press ENTER  three times. This will display the current location. To keep an axis from moving Press ENTER  when the axis value comes up.
 \\
-**Return to [[keypad_overview|the keypad overview]].**\\
+**Return to [[:en:x200:keypad_overview|the keypad overview]].** \\
 **Continue to [[:en:x200:table_of_contents|the table of contents]].**

cyborg-engravers

User Tools

Site Tools

Differences

Page Tools