| Both sides previous revision
Previous revision
Next revision
|
Previous revision
|
en:x200:home_calibration [2025/04/23 15:48]
erik.ketele |
en:x200:home_calibration [2025/04/23 15:52] (current)
erik.ketele |
| |{{ :en:x200:dsc03863.jpg?500 |{afbeelding}}|Gently rotate the black knob on the back side of the X-axis stepper motor till the flat side of the cutter is well aligned with the left table stop.| | |{{ :en:x200:dsc03863.jpg?500 |{afbeelding}}|Gently rotate the black knob on the back side of the X-axis stepper motor till the flat side of the cutter is well aligned with the left table stop.| |
| |{{ :en:x200:dsc03872.jpg?500 |{afbeelding}}|Now check if the finely engraved line on this knob corresponds with the engraved line on the indicator plate.\\ If that is not the case, loosen the black knob and rotate it to properly align it with the engraved indicator plate.| | |{{ :en:x200:dsc03872.jpg?500 |{afbeelding}}|Now check if the finely engraved line on this knob corresponds with the engraved line on the indicator plate.\\ If that is not the case, loosen the black knob and rotate it to properly align it with the engraved indicator plate.| |
| | |Re-tighthen this knob.| | | |Re-tighthen this knob.|\\ |
| | | |Screw the depth regulator nose back onto the spindle.| |
| |
| \\ | \\ |
| |{{ :en:x200:dsc03862.jpg?500 |{afbeelding}}|Jog the Z-axis (the spindle) down till there is about 15 mm distance to the table surface.\\ After that screw a cutter knob counter clockwise in the spindle.\\ Then gently push a cutter through the cutter knob and the spindle. It has to stick out of the spindle at the bottom.\\ Push the cutter through the spindle till its tip is as close as possible to the table surface, but without touching it.\\ Tighthen the cutter knob screw. | | |{{ :en:x200:dsc03862.jpg?500 |{afbeelding}}|Jog the Z-axis (the spindle) down till there is about 15 mm distance to the table surface.\\ After that screw a cutter knob counter clockwise in the spindle.\\ Then gently push a cutter through the cutter knob and the spindle. It has to stick out of the spindle at the bottom.\\ Push the cutter through the spindle till its tip is as close as possible to the table surface, but without touching it.\\ Tighthen the cutter knob screw. | |
| |{{ :nl:x200:vacconnect.png?500 |{afbeelding}}|Switch off the machine using the mainswitch.| | |{{ :nl:x200:vacconnect.png?500 |{afbeelding}}|Switch off the machine using the mainswitch.| |
| |{{ :en:x200:dsc03863.jpg?500 |{afbeelding}}|Gently rotate the black knob on the back side of the Y-axis stepper motor till the flat side of the cutter is well aligned with the rear table stop.| | |{{ :en:x200:dsc03866.jpg?500 |{afbeelding}}|Gently rotate the black knob on the back side of the Y-axis stepper motor till the flat side of the cutter is well aligned with the rear table stop.| |
| |{{ :en:x200:dsc03880.jpg?500 |{afbeelding}}|Now check if the finely engraved line on this knob corresponds with the engraved line on the indicator plate.\\ If that is not the case, loosen the black knob and rotate it to properly align it with the engraved indicator plate.| | |{{ :en:x200:dsc03880.jpg?500 |{afbeelding}}|Now check if the finely engraved line on this knob corresponds with the engraved line on the indicator plate.\\ If that is not the case, loosen the black knob and rotate it to properly align it with the engraved indicator plate.| |
| | |Re-tighthen this knob.| | | |Re-tighthen this knob.|\\ |
| | | |Screw the depth regulator nose back onto the spindle.| |
| \\ \\ \\ | \\ \\ \\ |
| **Continue to [[:en:x200:home_calibration|The engraved data are not positioned correctly on the plate.]].** \\ | **Continue to [[:en:x200:home_calibration|The engraved data are not positioned correctly on the plate.]].** \\ |
