cyborg-engravers

User Tools

Site Tools

Trace:
en:x200:engraving_without_floating_nose

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision 		Previous revision
en:x200:engraving_without_floating_nose [2025/04/18 12:16]
erik.ketele created 		en:x200:engraving_without_floating_nose [2025/04/23 21:46] (current)
erik.ketele
Line 1: Line 1:
-====== 3.4.2. Engraving without without floating nosecone ======+====== 3.4.2. Engraving without floating nosecone ======
  
-- In this chapter we explain how the plate surface (Z=0.0) can be defined (see 3.4.2.1). \\+- In this chapter we explain how the plate surface (Z=0.0) can be defined (see 3.4.2.1).\\
 - Then you will read which procedure has to be followed to enter engraving depths in Symmetry. (see 3.4.2.2.)\\ - Then you will read which procedure has to be followed to enter engraving depths in Symmetry. (see 3.4.2.2.)\\
 - After that follows the explanation how to mechanically prepare the machine to work without nosecone. (see 3.4.2.3.)\\ - After that follows the explanation how to mechanically prepare the machine to work without nosecone. (see 3.4.2.3.)\\
 - Finally the execution of the engraving job with locked spring pressure. (zie 3.4.2.4.) - Finally the execution of the engraving job with locked spring pressure. (zie 3.4.2.4.)
  
-  * [[:nl:x200:define_z-offset_when_surfacing|3.4.2.1. Defining the plate surface]] +  * [[:en:x200:define_z-offset_when_surfacing|3.4.2.1. Defining the plate surface]] 
-  * [[:nl:x200:how_to_use_symmetry_engraving_depths|3.4.2.2. Instelling om de in Symmetry ingestelde graveerdieptes te gebruiken]] +  * [[:en:x200:how_to_use_symmetry_engraving_depths|3.4.2.2. How to enter engraving depths in Symmetry]] 
-  * [[:nl:x200:how_to_lock_the_spring_pressure|3.4.2.3. De veerdruk blokkeren om zonder diepteneus te graveren]] +  * [[:en:x200:how_to_lock_the_spring_pressure|3.4.2.3. Locking the spindle spring to engrave without nosecone]] 
-  * [[:nl:x200:executing_a_job_without_nosecone|3.4.2.4. Executing a job without using the nosecone]]+  * [[:en:x200:executing_a_job_without_nosecone|3.4.2.4. Executing a job without using the nosecone]]
  
-**Ga verder naar [[:nl:x200:define_z-offset_when_surfacing|3.4.2.1. Bepalen van het plaatoppervlak]].** \\ **Ga verder naar [[:nl:x200:inhoudstafel|de inhoudstafel]].**+**Continue to [[:en:x200:define_z-offset_when_surfacing|3.4.2.1. Defining the plate surface]].** \\ **Continue to [[:en:x200:table_of_contents|the table of contents]].**
  
  
en/x200/engraving_without_floating_nose.1744971375.txt.gz · Last modified: 2025/04/18 12:16 by erik.ketele

Page Tools

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki